Threaded spheres

OT EQUATOR M1.6

The OT Equator CAD/CAM line with 1.6 mm thread consists of a universal threaded titanium sleeve and an OT Equator attachment. The system can be used for CAD/CAM workflows and with the traditional lost-wax technique.

The threaded sleeve can be bonded and used interchangeably for OT Equator, OT Cap Normo and OT Cap Micro. The attachments feature a 1.6 mm thread.

Whether using the CAD/CAM system or the traditional technique, the result is always the same: maximum precision and interchangeability.

PRODUCT INFO

DENTAL CLINIC

LABORATORY

PRODUCT SPECIFICATIONS

VIDEO

PRODUCT INFO

Ref. 160EQB

OT EQUATOR THREADED SLEEVE SYSTEM KIT
FOR BONDING

Kit contains:

• 2 EQUATOR THREADED (for titanium sleeve 1.6 mm thread)
• 2 THREADED SLEEVES (1.6 mm thread)
• 2 STAINLESS STEEL HOUSINGS
• 2 EQUATOR SPACERS
• 8 RETENTIVE CAPS (2 extra-soft, 2 soft, 2 standard, 2 processing)

Ref. 192ECE

CAPS ASSORTMENT KIT

Kit contains:

• 1 STAINLESS STEEL HOUSING
• 1 PROCESSING CAP
• 1 PROTECTIVE DISK
• 4 RETENTIVE CAPS (1 extra-soft, 1 soft, 1 standard, 1 strong)

SPARE PARTS

Ref. 339SFE

• 1 OT EQUATOR (for titanium sleeve - threaded 1.6mm)

Ref. 239GSF

• 1 TITANIUM SLEEVE (1.6mm threaded)

Ref. 339SSE

• 1 OT EQUATOR SPACER

Ref. 140CEV

• 4 RETENTIVE CAPS / VIOLET (strong 2700g)

Ref. 140CET

• 4 RETENTIVE CAPS / CLEAR (standard 1800g)

Ref. 140CER

• 4 RETENTIVE CAPS - PINK “SOFT” 1200g

Ref. 140CEG

• 4 RETENTIVE CAPS / YELLOW (extra-soft 600g)

Ref. 140CEN

• 4 RETENTIVE CAPS  / BLACK (for laboratory use only)

Ref. 141CAE

• 2 STAINLESS STEEL HOUSINGS

Ref. 141CTE

• 2 TITANIUM HOUSINGS / FUCHSIA ANODIZED

TOOLS

Ref. 776CGC

• 1 SQUARE SCREW DRIVER for tightening OT EQUATOR
(SQUARE TIP 1.25MM) (USABLE WITH THE MANUAL TORQUE WRENCH)

Ref. 760CQC

• 1 OT EQUATOR SCREWDRIVER/STEM FOR TORQUE CONTROLLER WITH SQUARE CONICAL TIP

Ref. 485IC

• 1 MULTIUSE CAPS INSERTER/EXTRACTOR TOOL

Ref. 760CRD

• 1 RATCHET TORQUE CONTROL DEVICE
(FOR OT EQUATOR, SPHERO BLOCK AND FLEX 15/35NCM STRENGTH - MAX 50NCM TORQUE, SUGGESTED 25NCM)

LABORATORY

Step by step threaded sleeve bonding procedure

Once the bar has been connected with wax, create an area where the attachment spacer will be placed.

Apply separator to the base of the attachment spacer and postion using the parallelometer key.

With the attachment spacer in position, complete the wax-up design.

Carefully remove the attachment spacers and proceed with the NORMAL  casting procedure.

Screw the threaded attachment of choice (MICRO Ball shown) into the threaded sleeve.

Place the assembled attachment into the parallelometer key. Use a self curing metal to metal bonding composite on the sleeve and in the cylinder.

After the composite is cured, remove any excess material.


Unscrew the attachment to verify if the threaded sleeve is securely bonded in place.

The finished bar complete with attachments.

The technique is the same for all three attachment models

PRODUCT SPECIFICATIONS

VIDEO